| Customization: | Available |
|---|---|
| After-sales Service: | 24 Hours Technical Support by Email, Call, Video |
| Warranty: | One Year |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
All over the world, there are many kinds of used or exchanged waste wires and telecommunication cables. Our aim is to overcome the loss of copper and other by-products in regeneration treatment and make them more scientific and automatic. It cuts down personnel, improves the recovery rate, and thus improves production efficiency. It not only develops the national economy and protects the environment, but also is conducive to the development of the recycling industry.
Introduction
This Dry Type Copper Cable Recycling Machines is mainly used for recycling scrap copper wire, waste wire, waste cable and so on. The cable processed diameter less than 20mm, better for single conductor diameter of 0.2-0.5mm. Simply speaking, it is to crush the waste copper wire, wire and cable first, and then separate the crushed copper and plastic to achieve the distribution and utilization after separation. Because the separated copper looks as big as rice grain, it is called "copper rice machine", which can also be seen that it is an environmentally friendly mechanical product.
Working process
1. Crush.
First crush the cable wires into copper and plastic granules. After crushing, the size of granules are generally 2-8 mm.
2. Separation.
Using the principle of different specific gravity of metal (copper) and non-metal (plastic), two kinds of media with different specific gravity are separated by air flow and vibration.
Advantage
After crushing and processing scrap cables and wires, automatic mechanical separation can completely separate copper and plastics, and achieve the purpose of comprehensive utilization, with high economic benefits. In addition, the equipment is an integral combination structure, easy to install and debug, and transport (customers can be purchased after the power supply can be produced), stable performance.
1. Compact structure, beautiful appearance, reasonable layout and convenient installation.
2. Fully automatic intelligent control makes the equipment feed uniformly and operate intelligently, which makes the operation more convenient, time-saving and labor-saving, and ensures the stable operation of the equipment to the greatest extent.
3. The crusher is roll-to-roll, with low speed, high torque, large output, low noise and simple operation.
4. Platform combination is adopted for crusher, separating equipment, dust collecting equipment, which makes the equipment easy to move and transport, and increases the flexibility of equipment.
5. The alternating cutter shaft is used in the rotor of the crusher, which makes the crusher more efficient, less noisy and more stable in operation.
6. The sorting rate of air separation equipment is over 99%.
7. The recycling system makes the semi-finished products comminuted twice, which ensures the complete separation of metal and non-metal.
8. Bag dust collecting equipment can effectively control dust spillover, and the dust removal efficiency is over 99%.
Protective Devices
1). There is a protective baffle inside the material inlet to prevent crushed material from casting out of the feeding mouth.
2). High-speed rotating flywheels and belt transmission parts are covered with fixed protective covers.
Noise Level
1). The machine's unloading noise level is below 80dB.
2). Special Note: when the machine is working, the noise would increase as the machine's working load is increasing, so the operator must wear protective earplugs in working.
Use & Maintenance
In the case of correct selection of machines, the service life also depends on appropriate use and timely maintenance. High temperature complex lithium base grease is used for bearings, so they are high temperature resistant, good at impact resistance, have a long service life. According to the actual use, users shall regularly inject grease. When Chopper blades get blunt, remove the blades and sharpen them with a blade sharpening machine, and adjust the spacing between fixed blades and rotating blades to 0.15mm-0.25mm. The grease for bearings should be replaced every 300 working hours, and grease for chains shall be added every 15000 working hours.
Scrap cable wires: below 20mm
Final products:
Copper Cable Recycling Machines Show:
Blade and screen:
| Model | Dimension (cm) | Total Power (Kw) | Capacity (Kg/h) | Weight (Kg) |
| M400 | 150*150*190 | 11.92 | 100 | 750 |
| 400 | 270*190*230 | 23.12 | 150-200 | 1200 |
| 600A | 400*195*230 | 48.36 | 300-400 | 3400 |
| 600B | 430*195*240 | 52.36 | 300-400 | 3400 |
| 800 | 920*410*240 | 78.76 | 500-800 | 8000 |
| 1200 | 1600*1000*300 | 129.36 | 1000-1500 | 12000 |
| Serial number | Description | Quantity | Power (kw) |
| 1 | crusher | 1 set | 7.5 |
| 2 | Blower fan | 1 set | 2.2 |
| 3 | dust collector blower | 1 set | 1.5 |
| 4 | Vibrator motor | 1 sets | 0.36 |
| 5 | Small vibrator | 2 set | 0.18 |
Copper Cable Recycling Machines
Service for Copper Cable Recycling Machines
1. The machines except spare parts are guaranteed for 12 months.
2. Engineer will be sent to your place to guide how to operate for the production line.
3. We will send you extra set of spare parts and two sets small vibrators.
1.Is there wearing part on the Copper Cable Recycling Machines?
Yes.
The spare parts is blades and screen, their use life is more than 2 years, there is a special blade sharping machine for blades maintenance, we can supply it if need.
2. What's the lognest continuous working time for this copper cable wires granulator machine?
Normally 10 hours per day.
3. Is the machine easy to operate? How many workers required to operate it?
This machine has precise and simple control system.
For small copper wire recycling machine, one worker is enough.
For complete copper recycling line, two workers are required.
){kind=link}