Innovative Wood Shaving Machine for Enhanced Production Efficiency

Product Description

Factory Direct Sales Wood Shaving Pier Plywood Pallet Footer Production Line

Product Description

The sawdust pallet feet block heat press machine production line we provide generally includes wood shredders, pipe dryers or  tumble dryers, glue mixers, shaving pallet foot pier machines, and wood pallet feet pier automatic block cutters.

Workflow of automatic production line for pallet foot pier:
 
Crusher - Dryer - Mixer - Hot Press Forming Machine (1-4 sets) - Automatic pier cutting machine   
  
Introduction: Add glue to the raw material with 10% water content, put it into the mixer and mix evenly; then put it into the pier machine for hot pressing, and the long product will come out, according to the customer's requirements, use the automatic pier cutting machine to cut it into small squares.

There are three main models of foot pier machine: single outlet, double outlet, three outlet
 

Model	Double Head (one head in each side)	Four Head (two heads in each side)	Six Head (three heads in each side)
Size (mm)	4800*500*1450mm	4800*580*1450mm	4900*940*1450mm
Capacity	2-3 m3/24h	4-5 m3/24h	6-7 m3/24h
Glue water amount	100-120kg/m3
Density	550-600kg/m3
Weight	1000kg	1200kg	1600kg
Power	12kw	16-18kw	24kw

 

Machine details

Raw materials suitable for wood pallet feet pier production:

1. Suitable raw materials are wood shavings, sawdust, and scraps. The minimum blending ratio is wood shavings accounting for more than 30%.
2. Wood shavings are the best raw material. The production of pure wood chips uses a large amount of glue and the strength of the product is not as high as that of wood shavings.
3. The moisture content of raw materials should be controlled within 12%.
4. The shape of the raw material is best to be a wooden sheet as thin as a paper sheet within 3-5 cm, or crushed wood chips can also be used.

1. If your raw material is large size of woods, the solution for large wood block raw materials ---------- wood crusher

2.  Wet sawdust/chips/shavings Solution ----------Dryer
The sawdust dryer is to continuously add powdery wet sawdust into the drying pipe by using a screw conveyor. In the transportation and dispersion of high-speed hot air flow, the water in the wet material is evaporated to obtain powdery or granular dry products. It is mainly composed of air heater, feeder, air drying pipe, cyclone separator, fan and so on.

3.  Glue Mixer --- a machine for mixing glue and wood sawdust/shavings:

The commonly used glue in China is "urea-formaldehyde glue" in liquid form. Ingredients: urea and formaldehyde, solid content not less than 55%.
The time to stir the wood is 1-2 minutes, and the stirred wood cannot be used the next day.
The ratio of glue to raw material is 16%, 1000kg raw material to 160kg glue.

4. Wood pallet foot piers/leg/block hot press making machine: 

The raw materials are put into the crusher to be crushed into wood shavings, dried in the dryer, glued by the glue mixing machine, and then hydraulically formed by the abrasive tool of the hot press machine, and extruded into pallet foot products, then cut into required block length.

Our Advantages

Our shaving pier hot-pressing equipment: mainly use waste materials such as shavings and wood chips, mix with glue, dry through a dryer, apply glue with a glue mixer, and heat and press with a hot press to form.

The produced pallet pier has a smooth and flat surface, good water resistance (it will not crack after soaking in water for 48 hours, and will not crack when exposed to wind and sun), and has strong nailing force. We can customize molds according to the specifications and sizes required by customers. The products we make are exempt from inspection and fumigation for export, and the formaldehyde emission (E2) is in line with national standards. 1660N is an ideal material for making fumigation-free wooden pallet brackets (foot piers, legs). This product is mainly used to replace the foot piers used on log pallets, free of fumigation and heat treatment.

The current production specifications of our factory are: 75*75, 80*80, 80*100, 80*120, 90*90, 100*100, 100*115, 100*120, 110*130 and other models (double-sided single-head , double-sided double-head, vertical center hole, no hole type) hot press and related specifications of products, various models can be customized according to customer requirements.

Certifications

Packaging & Shipping

FAQ

When the wood chip pier machine is pressing the wood shavings, sometimes it will not form, and the pressed pier is very loose, or even pressed out of shape. What is the reason? ?

The reason why the sawdust pier is not formed can be seen from two or three aspects.
One is the raw material, the other is the glue, and the third is the hot pressing time.

1. Raw material problem

One is the moisture content of the raw material. The moisture content of raw materials is a very, very important indicator. The water content is generally required to be below 10%. Of course, this value is not absolute, and different raw materials have different requirements.
The second is the mixing ratio. If it is a mixed material, the mixing ratio of various components will also affect the molding rate.

2. Glue

The glue factor. Generally, liquid urea-formaldehyde glue is used. The main ingredients are urea and formaldehyde, and the water content is relatively high. It needs to be customized with a solid content of more than 55%.

3. Hot pressing time

heat stress factor. Adjusting the machine clearance is a technical job, you can consult our technical staff. The hot pressing time and temperature are determined according to the moisture content of the raw material. Generally, the time is controlled within 10s, and the temperature is controlled between 120-180°C.